中国电气传动网

第一电气传动平台



总访问量:301114

关键词搜索:

  • 电机
  • MapleSystems
  • 传感器
  • 发电机
  • 机器人
  • 工业机器人
  • 济南鑫贝西
  • 数控
  • TSINGBO

扫一扫

了解更多

eX-S110-XT快速以太网扩展器

点击图片查看原图
 
单价: 面议
品牌: Perle
销量: 累计出售 0
评价: 已有 0 条评价
人气: 已有 17 人关注
更新: 2019-09-03
数量: 减少 增加件 库存100件
立即购买   加入购物车   点击询价
       
 
公司基本资料信息
 

当您需要在极端温度下扩展以太网服务超出328英尺/100米的一般IEEE 802.3限制,并且新的光纤布线成本过高时,以太网扩展器是完美的解决方案。Perle以太网扩展器通过铜线透明地扩展到四个10/100以太网连接。使用单双绞线(CAT5 / 6/7)或以前用于报警电路,E1/T1电路,RS-232,RS-422,RS-485,CCTV和CATV应用的任何现有铜线。


Equipment found in traffic management, oil and gas pipelines, weather tracking, industrial and outdoor applications must function in temperatures that cannot be supported by a commercial based Ethernet Extender. With the ability to operate in industrial grade temperatures of -40F to +167F (-40C to +75C) along with a rugged steel casing, these simple and effective point to point Ethernet Copper Extenders are ideal to extend the distance between two industrial Ethernet devices subjected to harsh environments and severe temperatures such as security cameras, wireless access points, alarms, traffic controllers, sensors and tracking devices.

Perle’s advanced features such as link Pass-Through*, Interlink Fault Feedback*, and Loopback allow Network administrators to “see everything” for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle Ethernet Extenders the smart choice for IT professionals. eX-S110 Ethernet Extenders are also available with support for Commercial Temperature rangesmanaged networks with AAA security and high-density applications.

eX-S110-XT Fast Ethernet Extender Features

Extend Ethernet over twisted pairExtend an Ethernet link over category 5e, 6 and 7 cabling up to 10,000 feet ( 3 km )
Extend Ethernet over Coaxial cableExtend an Ethernet link over 75 ohm coaxial cable
High-Speed PerformanceUtilizes second generation VDSL2 technology ( ITU-T Recommendation G.993. ) . When operating under “Profile 30a”, Perle Ethernet extenders can provide an aggregate VDSL line rate capability of over 200 mbps.

Actual distance and performance may vary depending on the type / gauge and condition of the wire used.
Plug and Play operationPerle Ethernet Extenders will automatically configure your VDSL interlink connection. The CO/CPE peer association will be determined automatically by the Ethernet Extender. No need to set CO / CPE VDSL pairing.

once a connection is made, both ends will automatically adjust relevant VDSL parameters to optimize the level of bandwidth possible across the copper link.
link Pass-Through*With link Pass-Through the state of the 10/100base-TX Ethernet connection is “passed through” the VDSL link to the 10/100base-TX Ethernet connection on its remote peer. A managed switch on the remote end can then report the state (link up or link down) to its network management system so that any errors can be detected and recovered early.

Competitive Ethernet extenders without this feature will never detect or report any error conditions.
Interlink Fault Feedback*Similar to the link Pass-Through feature, a loss of VDSL link will drop the 10/100 ethernet ports on each end until the link recovers.
Auto-NegotiationThe Ethernet Extender supports auto negotiation on the 10/100base-TX interface.
Auto-MDIXAuto-MDIX (Automatic Medium-Dependent Interface crossover) detects the signaling on the 10/100 Ethernet RJ45 interface and determines the type of cable connected (straight-through or crossover) and automatically adopts a compatible pinout.
Fixed Speed and DuplexSome Ethernet equipment require a fixed speed and duplex be used or cannot auto-negotiate. By disabling Auto-Negotiation on the Ethernet Extender, a fixed speed of 10 or 100 mbps as well as Full or half Duplex can be configured through DIP switches.
VLANTransparent to tagged VLAN ( 802.1Q ) packets.
Transparent to IP Video compression protocolsFully transparent to such IP video compression schemes such as MPEG-4, H.264 and MJPEG.
Power Strain Relief strapA strain relief strap is provided to ensure a solid and secure power connection to the Ethernet Extender. Ideal for areas that may be exposed to vibration.
LoopbackWhen enabled, will perform a loopback on the copper VDSL Interlink.


硬件:

EtherneteX-1S110-XTeX-4S110-XT
Port1 port RJ45 – 10/100 base-TX - Shielded4 port RJ45 – 10/100 base-TX - Shielded
Auto-MDIXAuto-MDIX enables proper operation with either straight-through or crossover cabling
DistanceDistance up to 100 meters ( 328 feet ) as per IEEE 802.3
Maximum frame Size1522 bytes
VDSL – Interlink
RJ45, BNC, Terminal Block

Ethernet Extenders must be connected in pairs using unconditioned wire. Circuits that run through signal equalization equipment are not permitted.

TIP and RING are polarity insensitive. Surge suppression of 400 volts between TIP and RING. Choice of RJ45, BNC or terminal block models for VDSL link connector:

  • RJ45 – RING pin 4, TIP pin 5 (TIA 568 A/B)

  • BNC – Coaxial 50 and 75 ohm cable with BNC connector

  • Terminal Block – 2 position screw connectors for use with twisted pair telephone, alarm or serial cabling between 19 ( 0.9 mm ) and 26 AWG ( 0.44 mm ).

VDSL2 Line Rate/ReachActual distance and rates experienced will depend on condition and gauge of wire used. This Rate/Reach table applies to 24 AWG ( 0.5 MM ) twisted pair wiring on RJ45 (RJ) and terminal block (TB) models.High Speed AsymmetricReach ( Distance )VDSL Rate ( Mbps )feetmetersDownstreamUpstream50015210192100030510163150045790382000610622425007625510300091442535001000353High Speed SymmetricReach ( Distance )VDSL Rate ( Mbps )feetmetersDownstreamUpstream500152101101100030585101150045762472000610602925007624414300091430735001000294Long Reach SymmetricReach ( Distance )VDSL Rate ( Mbps )feetmetersDownstreamUpstream500152534410003055343250076239184000121925455001676171.97000213482.37500228672.28000243852.2Long Reach AsymmetricReach ( Distance )VDSL Rate ( Mbps )feetmetersDownstreamUpstream5001527816100030578162500762551040001219310.855001676200.670002134110.675002286100.68000243880.6
PowereX-1S110-XTeX-4S110-XT
Input Supply Voltage9 - 30 vDC, unregulated ( 12 vDC Nominal )
Current320 mA370 mA
Power Consumption3.8 watts4.4 watts
Power Connectors5.5mm x 9.5mm x 2.1mm barrel socket and 2 pin terminal Block


Power Adapter
Universal AC/DC adapterOptional Industrial Temperature 100-240v AC, regulated 12V DC adapter
Indicators
Power / TSTThis green LED is turned on when power is applied to the Ethernet Extender. Otherwise it is off. The LED will blink when in Loopback test mode.
CO - LocalEthernet Extender is operating in CO VDSL mode
CPE - remoteEthernet Extender is operating in CPE VDSL mode
ILNKIndicates link Status and activity on the Interlink (VDSL) port
ETHIndicates link status and activity on Ethernet port(s).
SwitcheseX-1S110-XTeX-4S110-XT
AccessAll switch settings are accessible through a side opening in the chassis

Rate/ReachTwo switches enable the user to select the right balance between speed and distance for their environment.
Signal to Noise RatioSelectable Signal to Noise Ratio (SNR) of 6dB or 9dB. The higher SNR number provides better impulse noise protection but lowers performance.
Auto-Negotiation (802.3u)Enabled (Default) - The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100base-TX interface. It is set to advertise full duplex.

Disabled - The Ethernet Extender sets the port according to the position of the speed and duplex switches.

link ModeStandard (Default) – The 10/100base-TX link remains active independent of the state of the Ethernet link on its remote peer.

link Pass-Through- state of the 10/100base-TX Ethernet connection is “passed through” or propagated across the VDSL link to the 10/100base-TX Ethernet link on its remote Ethernet Extender peer. This enables a managed switch to report the state of the remote device to its network management system.

N/A
Interlink Fault FeedbackEnabled - A loss of VDSL link will drop the 10/100 Ethernet port on each end until the link recovers

Disabled ( Default ) – The state of the VDSL link is not propagated to the 10/100base-TX port

N/A
LoopbackEnabled - The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its peer.

Disabled (Default - Up)

Set Ethernet Speed
(Port 1)
When Auto-Negotiation switch is disabled, fixed speed can be set to 100 (Default) or 10
Set Ethernet Duplex
(Port 1)
When Auto-Negotiation switch is disabled, Duplex can be set to Full (Default) or Half
Environmental SpecificationseX-1S110-XTeX-4S110-XT
Operating Temperature-40°C to 75°C (-40°F to 167°F)
Storage Temperatureminimum range of -40°C to 85°C (-40°F to 185°F)
Operating Humidity5% to 90% non-condensing
Storage Humidity5% to 95% non-condensing
Operating AltitudeUp to 3,048 meters (10,000 feet)
Heat Output ( BTU/HR )13.115.2
MTBF (Hours)**466,387365,077
Mounting
Din Rail KitOptional
Rack Mount KitOptional
Product Weight and Dimensions
Weight0.33 kg, 0.73 lbs0.47 kg, 1.04 lbs
Dimensions120 x 80 x 35 mm, 4.7 x 3.1 x 1.4 inches130 x 115 x 35 mm, 5.1 x 4.5 x 1.4 inches
Packaging
Shipping Weight0.46 kg, 1.01 lbs0.65 kg, 1.43 lbs
Shipping Dimensions170 x 260 x 70 mm, 6.7 x 10.2 x 2.8 inches
Regulatory Approvals
EmissionsFCC Part 15 Class A, EN55022 Class A
CISPR 32:2015/EN 55032:2015 (Class A)
EN61000-3-2
ImmunityCISPR 24:2010/EN 55024:2010
Electrical SafetyUL 60950-1
IEC 60950-1(ed 2); am1, am2
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
CE
EnvironmentalReach, RoHS and WEEE Compliant
OtherECCN: 5A991
HTSUS Number: 8517.62.0050
Perle Lifetime warranty


选型: