中国电气传动网

第一电气传动平台



总访问量:277998

关键词搜索:

  • 电机
  • 济南鑫贝西
  • 上海仪电
  • 英国马尔文
  • 传感器
  • 发电机
  • 机器人
  • 工业机器人
  • 数控

扫一扫

了解更多

eXP-S110 PoE高速以太网扩展器

点击图片查看原图
 
单价: 面议
品牌: Perle
销量: 累计出售 0
评价: 已有 0 条评价
人气: 已有 48 人关注
更新: 2019-07-23
数量: 减少 增加件 库存100件
立即购买   加入购物车   点击询价
       
 
公司基本资料信息
 

Perle eXP-S110 PoE快速以太网扩展器透明地将以太网扩展到超过328英尺/ 100米的一般IEEE 802.3af限制,同时为基于标准的兼容设备(如IP摄像机,VoIP电话和无线接入点)提供以太网供电(PoE)。


This technology enables users to transparently extend up to four 10/100 Power over Ethernet connections across copper wiring. Use single twisted pair ( CAT5/6/7 ), coax or any existing copper wiring previously used in alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV and CATV applications.

At the central site, the 10/100 Ethernet Extender has full PoE support and operates as a Powered Device (PD) under IEEE 802.3af supporting end-span and mid-span power sources (PSE). Alternatively, the unit can be powered by the included 48v adapter. The PoE Ethernet Extender at the central site then transmits power over the copper wire to power the remote PoE Ethernet Extender and attached PD. The remote PoE Ethernet Extenders are classified as Power Sourcing Equipment (PSE). While using standard UTP cables that carry Ethernet data, Perle eXP-S110 PoE Ethernet Extenders provide up to 15.4 watts of power to Powered Devices (PDs). For longer distance applications the remote PoE Extender (CPE) can be powered by a local 48v adapter. Learn more about PoE.

These simple and effective point to point Ethernet Copper Extenders are perfect for commercial buildings, residential units, hospitality environments, and connecting a remote office or private-network backbone to a corporate LAN … anywhere you need 10/100 Ethernet communication links for PoE devices up to 10,000ft (3KM) in distance.

Perle’s advanced features such as link Pass-Through* and Interlink Fault Feedback*, Loopback and remote PD reset*, enable Network administrators to “see everything” for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle Ethernet Extenders the smart choice for IT professionals. eXP-S110 PoE Fast Ethernet Extenders are also available with support for Extended Temperature Environments.

eXP-S110 PoE Fast Ethernet Extender Features

Extend Ethernet over twisted pairExtend an Ethernet link over category 5e, 6 and 7 cabling up to 10,000 feet ( 3 km )
Extend Ethernet over Coaxial cableExtend an Ethernet link over 75 ohm coaxial cable
On-board PoE Power ControllerAs a fully compliant IEEE 802.3af PSE end-span device, this Ethernet Extender’s PoE power controller provides compliant power provisioning and monitoring, properly sensing through signature detection whether or not the attach Ethernet devices are PoE capable or not. This provides a safe connection for both PoE and Non-PoE capable devices.

Competitive PoE Ethernet Extender products operate as a simple passive power injector and will always apply power to RJ45 port pins which may result in damage if non-PoE compliant Ethernet devices are accidently attached.

Click here for more details
Advanced Power capabilities
  • ALT A/B and legacy PoE RJ45 pin selection

  • Current limiting protection

  • Remote PD reset

Fully compliant 802.3af POE PSE
  • Enable/Disable PSE power

  • PD signature detection

  • Over-Current Protection

  • PD power classification detection ( Class 0,1,2,3)

Fully Compliant 802.3af/at PoE PDonly PoE Ethernet Extender solution that provides a Class 0 or 4 signature to PSE for proper operation with PSE equipment such as Cisco PoE switches.

Competitive PoE Ethernet extender solutions cannot be powered by Cisco PoE switches as they cannot provide the necessary PoE PD signature required by the switch. Without this, the switch will not supply power at all.
PSE Status IndicatorA multi-color LED provided presents the status of the PSE function for easy troubleshooting of power over Ethernet connections
PD Power Reset ( Port 1 )Ideal for remotely resetting equipment, this configurable function performs a momentary power reset to the attached Powered Device (PD) on Port #1.

Read our 
PD Reset Tech Note for further details on this feature
Power Multiplier SelectionWhen used with 4-pair cable such as CAT5 on the VDSL Interlink port, an optional internal strap selection on the Ethernet Extender will provide VDSL transmission data on 1 pair and power across the 3 other pairs enabling even greater distances for power transmission to be achieved.
Broadest range of PoE devices supportedSupport is included for a broad range of PD ( Powered Devices )

  • IEEE 802.3af PoE ( Alternative A and B )

  • Legacy High Capacitance PDs

  • Cisco legacy VoIP phones and Wireless Access Points

High-Speed PerformanceUtilizes second generation VDSL2 technology ( ITU-T Recommendation G.993. ). When operating under “Profile 30a”, Perle Ethernet Extenders can provide an aggregate VDSL line rate capability of up to 200 mbps.

Actual distance and performance may vary depending on the type / gauge and condition of the wire used and if required, the amount of power you require across the VDSL link
Plug and Play operationPerle Ethernet Extenders will automatically configure your VDSL interlink connection. The CO/CPE peer association will be determined automatically by the Ethernet Extender. No need to set CO / CPE VDSL pairing.

once a connection is made, both ends will automatically adjust relevant VDSL parameters to optimize the level of bandwidth possible across the copper link.
link Pass-Through*With link Pass-Through the state of the 10/100base-TX Ethernet connection is “passed through” the VDSL link to the 10/100base-TX Ethernet connection on its remote peer. A managed switch on the remote end can then report the state (link up or link down) to its network management system so that any errors can be detected and recovered early.

Competitive Ethernet extenders without this feature will never detect or report any error conditions.
Interlink Fault Feedback*Similar to the link Pass-Through feature, a loss of VDSL link will drop the 10/100 Ethernet port on each end until the link recovers.
Auto-NegotiationThe Ethernet Extender supports auto negotiation on the 10/100base-TX interface
Auto-MDIXAuto-MDIX (Automatic Medium-Dependent Interface crossover) detects the signaling on the 10/100 Ethernet RJ45 interface and determines the type of cable connected (straight-through or crossover) and automatically adopts a compatible pinout.
Fixed Speed and DuplexSome Ethernet equipment require a fixed speed and duplex be used or cannot auto-negotiate. By disabling Auto-Negotiation on the Ethernet Extender, a fixed speed of 10 or 100 mbps as well as Full or half Duplex can be configured through DIP switches.
VLANTransparent to tagged VLAN ( 802.1Q ) packets.
Transparent to IP Video compression protocolsFully transparent to such IP video compression schemes such as MPEG-4, H.264 and MJPEG.
Power Strain Relief strapA strain relief strap is provided to ensure a solid and secure power connection to the Ethernet Extender. Ideal for areas that may be exposed to vibration.
LoopbackWhen enabled, will perform a loopback on the copper VDSL Interlink.


硬件:

Remote ( Power over Ethernet )Local ( power over link - VDSL )
PowereXP-1S110EeXP-4S110EeXP-1S110LeXP-4S110L
Unit Powered byLocal power adapter or VDSL
  • Local power adapter or

  • PoE Power Sourcing Equipment such as a Cisco PoE+ Switch on port #1

  • PoE+ power injector

Provides Power to:EthernetLink ( VDSL Interlink )
Power adapter connectorBarrel or terminal block
Input Voltage Range from adapter46V to 5729 to 57
Input Voltage Range from VDSL (parasitic)24 to 57N/A
Universal AC Adapter48vDC, 60 watts is included when purchased an individual basis. One 48vDC 60 watts adapter is provided in each kit.
Power Connectors5.5mm x 9.5mm x 2.1mm barrel socket and 2 pin terminal Block

Remote ( Power over Ethernet )Local ( power over link - VDSL )
EtherneteXP-1S110EeXP-4S110EeXP-1S110LeXP-4S110L
10/100base TX Port(s)1 port RJ45 Shielded4 port RJ45 Shielded1 port RJ45 Shielded4 port RJ45 Shielded
Auto-MDIXAuto-MDIX enables proper operation with either straight-through or crossover cabling
DistanceDistance up to 100 meters ( 328 feet ) as per IEEE 802.3
Maximum frame Size1522
Type of PoE devicePSE ( PoE ) IEEE 802.3afPD ( Class 0 or 4 device )
PoE PSE Maximum Power (Watts)Refer to the Power Reach Installation Planning GuideN/A
PoE PSE RJ45 Cable PinoutAlternative A ( default ) on all ports
Pins 3,6 Neg, Pins 1,2 Pos

Alternative B: selectable on port #1
Pins 7,8 Neg, Pins 4,5 Pos

Legacy Cisco Pre-Standard: selectable on port #1
Pins 7,8 Pos, Pins 4,5 Neg

N/A

Remote ( Power over Ethernet )Local ( power over link - VDSL )
VDSL – InterlinkeXP-1S110EeXP-4S110EeXP-1S110LeXP-4S110L
RJ45, BNC, Terminal Block

Ethernet Extenders must be connected in pairs using unconditioned wire. Circuits that run through signal equalization equipment are not permitted.

TIP and RING are polarity insensitive. Surge suppression of 400 volts between TIP and RING. Choice of RJ45, BNC or terminal block models for VDSL link connector:

  • RJ45 – RING pin 4, TIP pin 5 (TIA 568 A/B)

  • BNC – Coaxial 50 and 75 ohm cable with BNC connector

  • Terminal Block – 2 position screw connectors for use with twisted pair telephone, alarm or serial cabling between 19 ( 0.9 mm ) and 26 AWG ( 0.44 mm ).



Power Injection over the Interlink ( VDSL ) – 2-wireN/AInjects SELV compliant voltage and VDSL data across a single pair of cooper wires ( pins 4 and 5 ) or 2 conductor BNC coaxial cable
Short Circuit ProtectionN/AShort Circuit protection provided
Reverse Polarity ProtectionThe voltage from the VDSL link requires proper polarity in order to provide power to the remote extender. Reverse polarity protection however will ensure that there is no damage to the extenderN/A
Power Multiplier SelectionWhen used with 4-pair cable such as CAT5 on the VDSL Interlink port, an optional internal strap selection on the Ethernet Extender will provide VDSL transmission data on 1 pair and power across the 3 other pairs enabling even greater distances for power transmission to be achieved
VDSL Line Rate/ReachActual distance and rates experienced will depend on condition and gauge of wire used. This Rate/Reach table applies to 24 AWG ( 0.5 MM ) twisted pair wiring on RJ45 (RJ) and terminal block (TB) models.High Speed AsymmetricReach ( Distance )VDSL Rate ( Mbps )feetmetersDownstreamUpstream50015210192100030510163150045790382000610622425007625510300091442535001000353High Speed SymmetricReach ( Distance )VDSL Rate ( Mbps )feetmetersDownstreamUpstream500152101101100030585101150045762472000610602925007624414300091430735001000294Long Reach SymmetricReach ( Distance )VDSL Rate ( Mbps )feetmetersDownstreamUpstream500152534410003055343250076239184000121925455001676171.97000213482.37500228672.28000243852.2Long Reach AsymmetricReach ( Distance )VDSL Rate ( Mbps )feetmetersDownstreamUpstream5001527816100030578162500762551040001219310.855001676200.670002134110.675002286100.68000243880.6This table applies when the power multiplier option is selected
Power BudgetThe amount of available power at the PoE PD is dependent on the scenario planned.
Refer to the 
Power Reach Installation Planning Guide

Remote ( Power over Ethernet )Local ( power over link - VDSL )
IndicatorseXP-1S110EeXP-4S110EeXP-1S110LeXP-4S110L
Power / TSTThis green LED is turned on when power is applied to the Ethernet Extender. Otherwise it is off. The LED will blink when in Loopback test mode.
CO - LocalEthernet Extender is operating in CO VDSL mode
CPE - remoteEthernet Extender is operating in CPE VDSL mode
ILNKIndicates link Status and activity on the Interlink (VDSL) port
ETHIndicates link status and activity on Ethernet port(s).
PSE StatusThis LED will signify the status of the PSE function. Using multi-color and blinking the unit will show the following status for the PSE;

GREEN — Solid: The PSE has successfully detected a compliant PD and is applying power over the UTP (for legacy pin out simply show active power when applied)

YELLOW — Solid: The PSE is not active. This means the PSE has been configured to provide power, but the PD is :

  • Not connected

  • Has not detected a compliant PD and is not applying power

  • PSE has turned off power for Reset function


OFF — PSE function switch disabled

RED — Blinking: Error Conditions

  • Capacitance too High — 1 blink

  • Resistance too Low or short circuit — 2 blinks

  • Resistance too high or open circuit — 3 blinks



Remote ( Power over Ethernet )Local ( power over link - VDSL )
SwitcheseXP-1S110EeXP-4S110EeXP-1S110LeXP-4S110L
AccessSwitch settings are accessible through a side opening in the chassis
Rate/ReachTwo switches enable the user to select the right balance between speed and distance for their environment.
Signal to Noise RatioSelectable Signal to Noise Ratio (SNR) of 6dB or 9dB. The higher SNR number provides better impulse noise protection but lowers performance.
Auto-Negotiation (802.3u) control on Port 1Enabled (Default) - The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100base-TX interface. It is set to advertise full duplex.

Disabled - The Ethernet Extender sets the port according to the position of the speed and duplex switches.

Force Ethernet Speed on Port 1When Auto-Negotiation switch is disabled, a fixed speed can be forced on port 1 to 100 (Default) or 10
Force Ethernet Duplex on Port 1When Auto-Negotiation switch is disabled, Full or half Duplex can be forced on port 1 to Full (Default) or Half
link ModeStandard (Default) – The 10/100base-TX link remains active independent of the state of the Ethernet link on its remote peer.

link Pass-Through- state of the 10/100base-TX Ethernet connection is “passed through” or propagated across the VDSL link to the 10/100base-TX Ethernet link on its remote Ethernet Extender peer.

Interlink Fault FeedbackEnabled – A loss of VDSL link will drop the 10/100 Ethernet port on each end until the link recovers

Disabled ( Default ) - The state of the VDSL link is not propagated to the 10/100base-TX port

LoopbackEnabled – The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its remote peer.

Disabled (Default - Up)

PoE PD Class selectionN/A( Internal strap ) for PoE PD classification type identification for attached IEEE 802.3at compliant PoE+ switch on port #1

Class 0 – PoE PD device - 0.44-12.94W ( Default )

Class 4 – PoE+ PD device 12.95 – 25.5W

PD Reset ( Port 1 )When enabled ( down ), the Ethernet Extender will upon loss of link on the VDSL Interlink port, turn off PSE output power to the PD device for 2 seconds then turn the power back on. The power remains on until the VDSL link transitions from up to down again.

When PD Power Reset is disabled ( default ), loss of VDSL link has no effect on power supplied to the PD.

N/A
Environmental SpecificationseXP-1S110EeXP-4S110EeXP-1S110LeXP-4S110L
Operating Temperature0 C to 50 C (32 F to 122 F)
Storage Temperatureminimum range of -25 C to 70 C (-13 F to 158 F)
Operating Humidity5% to 90% non-condensing
Storage Humidity5% to 95% non-condensing
Operating AltitudeUp to 3,048 meters (10,000 feet)
Current mA108 @ 48vdc121 @ 48vdc129 @ 48vdc142 @ 48vdc
Unit Power Consumption watts5.25.86.26.8
Heat Output
( BTU/HR )
17.7419.7921.1623.20
MTBF with power adapter (Hours)**185,061169,935199,390182,735
MTBF without power adapter (Hours)**300,472262,530340,165294,389
MountingeXP-1S110EeXP-4S110EeXP-1S110LeXP-4S110L
Wall/DeskStandard
Din Rail KitOptional
Rack Mount KitOptional
Product Weight and DimensionseXP-1S110EeXP-4S110EeXP-1S110LeXP-4S110L
Weight0.58 Kg, 1.3 lbs0.61Kg, 1.34 lbs0.58 Kg, 1.3 lbs0.61Kg, 1.34 lbs
Dimensions163 x 116 x 37 mm, 6.4 x 4.6 x 1.46 inches
PackagingeXP-1S110EeXP-4S110EeXP-1S110LeXP-4S110L
Shipping Weight1.27 Kg, 2.8 lbs1.3 Kg, 2.86 lbs1.27 Kg, 2.8 lbs1.3 Kg, 2.86 lbs
Shipping Dimensions20 x 30 x 7 cm, 7.9 x 11.8 x 2.8 inches
Regulatory ApprovalseXP-1S110EeXP-4S110EeXP-1S110LeXP-4S110L
EmissionsCISPR 32:2015/EN 55032:2015 (Class A)
IEC/EN 61000-3-2
IEC/EN 61000-3-3
ImmunityCISPR 24:2010/EN 55024:2010
IEC/EN 61000-4-2
IEC/EN 61000-4-3
IEC/EN 61000-4-4
IEC/EN 61000-4-5
IEC/EN 61000-4-6
IEC/EN 61000-4-8
IEC/EN 61000-4-11
Electrical SafetyUL 60950-1
IEC 60950-1(ed 2); am1, am2
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
CSA C22.2 No. 60950-1
EnvironmentalReach, RoHS and WEEE Compliant
OtherECCN: 5A991
HTSUS Number: 8517.62.0050
Perle Lifetime warranty


选型: