中国电气传动网

第一电气传动平台



总访问量:283319

关键词搜索:

  • 电机
  • 济南鑫贝西
  • 上海仪电
  • 英国马尔文
  • 传感器
  • 发电机
  • 机器人
  • 工业机器人
  • 数控

扫一扫

了解更多

S-10GRT-SFP媒体转换器

点击图片查看原图
 
单价: 面议
品牌: Perle
销量: 累计出售 0
评价: 已有 0 条评价
人气: 已有 58 人关注
更新: 2019-07-23
数量: 减少 增加件 库存100件
立即购买   加入购物车   点击询价
       
 
公司基本资料信息
 

Perle S-10GRT-SFP媒体转换器通过多模或单模光纤透明连接10/100/1000/2.5G/10Gbase-T以太网链路。 每个媒体转换器都配有一个RJ45以太网10Gbase-T端口和一个用于一个SFP或SFP +模块的空插槽。S-10GRT-SFP媒体转换器支持关键功能,可实现最佳的网络灵活性和增长。


  • 10/100/1000/2.5G/10G rate conversion can be enabled to automatically detect Ethernet port speed and do a rate conversion between the two ports if the Ethernet speed is different. This is ideal in scenarios where disparate networks need to be connected.

  • Cut-Through Forwarding can be configured for environments where throughput speed is critical. This will increase the media converter’s throughput and reduce latency by performing packet forwarding in the most efficient manner possible.

Copper to Fiber conversion is achieved by inserting SFP or SFP+ fiber transceivers that support multimode and single-mode fiber, including CWDM/DWDM wavelengths. Copper to copper is achieved by inserting SFP+ Direct Attach Cable (DAC), also known as twinax.

The empty transceiver port on the S-10GRT-SFP Media Converter allows for flexible network configurations to meet any requirement using a variety of transceivers supplied by Perle, Cisco or other manufacturers of MSA compliant SFPs. You can use this products to convert:

Copper to Fiber Conversion:

  • 10/100/1000/2.5G/10Gbase-T to 1G Fiber SFP

  • 10/100/1000/2.5G/10Gbase-T to 10G Fiber SFP+

Copper to Copper Conversion:

  • 10/100/1000/2.5G/10Gbase-T to 1G Copper SFP

The Perle S-10GRT-SFP Media Converter provides an economical path to extend Ethernet data transmission distances or convert network speeds. Network Administrators can “see-everything” with Perle’s advanced features such as Smart link Pass-Through, Fiber Fault alert and Loopback. This allows for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make the Perle S-10GRT-SFP Media Converter the smart choice for IT professionals. If you need a Media Converter that can operate in a managed environment with AAA security, check out the SMI-10GRT-SFP.

S-10GRT-SFP Media Converter Features

Rate ConversionThe Media Converter can automatically detect Ethernet port speed and do a rate conversion between the two ports if the Ethernet speed is different.
Cut-Through ForwardingWhen the same Ethernet speed for both ports is enabled, the Media Converter can be configured for Cut-Through Forwarding. This will increase the media converter’s throughput and reduce latency by performing packet forwarding in the most efficient manner possible. Forwarding of a packet will begin as soon as the destination address is processed.
SFP Speed SensingAutomatically detects whether a SFP has been inserted and adjusts the speed accordingly.
SGMII Interface SupportThe Media Converter supports 1000Mbps SGMII SFPs
Copper Auto-NegotiationsThe media converter supports auto negotiation on Ethernet copper interface port
Copper DuplexFull and half duplex operation is supported
Smart link Pass-ThroughWhen Smart link Pass-Through is enabled (default), each port will reflect the state of its port peer. In this mode, if a link loss is detected on one port, the transmit signal on the other port is disabled “passing through” the state of the failed link. This enables managed switches and other devices to report link failures to their network NMS.

When Smart link Pass-Through is disabled, if a link loss is detected on one port the transmit signal remains enabled on the other port.
Fiber Fault alertWith Fiber Fault alert the state of the 10 Gigabit Ethernet receiver is passed to the transmitter. This provides fault notification to the partner device attached to the 10G Ethernet interface of the media converter.
Green EthernetUtilizes Green Ethernet energy saving technology based on industry standards such as:
  • Energy Efficient Ethernet (EEE) as per 802.3az. This provides power savings during idle network activity.

Module Temperature ProtectionProtects your DOM/DMI capable SFP or SFP+ module by monitoring its internal temperature and will automatically shut down the SFP or SFP+ if the module is operating above its maximum temperature threshold.
Gigabit SFP supportThe 10 Gigabit media converter model with the SFP slot can also support Gigabit (1000base-X) SFPs. This allows users to use Gigabit SFPs today and migrate to 10G SFP+ in the future.
Jumbo PacketsTransparent to Jumbo frames with a maximum MTU size of 10,024 bytes
VLANTransparent to VLAN tagged packets.
Power Strain Relief strapA strain relief strap is provided to ensure a solid and secure power connection to the media converter. Ideal for areas that may be exposed to any vibration.
Remote LoopbackCapable of performing a loopback on the 10 Gigabit interface. In this mode, all frames received on the port in loopback mode will be transmitted back. This provides users with the capability of utilizing their own in-house test generators for testing the link.


硬件:

Power
Input Supply Voltage9 - 30 vDC, unregulated ( 12 vDC Nominal )
Maximum Power Consumption15.5 watts*
Power Connector5.5mm x 9.5mm x 2.1mm barrel socket
Power Adapter
Universal AC/DC Adapter100-240v AC, regulated AC/12v DC adapter included
Indicators
Power / TST
  • On: Power indication and in normal operation

  • Blinking slowly: the unit is in loopback or test mode (either port)

  • Red solid: the unit has a hardware error (upon power up)

  • Red and blinking: the unit has a hardware error specified by combination of LK1 and LK2

LK1 (SFP)
  • On: link present

  • Blinking quickly: Fiber link present and receiving data.(including test data)

  • Blinking slowly: Fiber link disabled because the other fiber link went down.

  • Blinking 1 sec on 3 sec off – module shut down due to high temperature.

  • Off: No fiber link present or no module inserted

LK2
  • On: 10Gbase-T link present

  • Blinking quickly: link present and receiving data

  • Blinking slowly: link disabled because link 1 went down

  • Off: 10Gbase-T link is not active

Switches - accessible through a side opening in the chassis
Smart link Pass-ThroughEnabled (Default - Up)

When the link Mode switch is enabled (default), each port will reflect the state of its port peer using Smart link Pass-Through. In this mode, if a link loss is detected on one port, the transmit signal on the other port is disabled “passing through” the state of the failed link. This enables managed switches and other devices to report link failures to their network NMS.

When the switch is in the down position, Smart link Pass-Through is disabled. If a link loss is detected on one port, the transmit signal remains enabled on the other port.

Fiber Fault alertEnabled (Default - Up)

With Fiber Fault alert the state of the 10 Gigabit ethernet receiver is passed to the transmitter. This provides fault notification to the partner device attached to the 10G ethernet interface of the media converter.

Cut-through / Rate convertingRate Converting (Default - Up)

The Media Converter can automatically detect Ethernet port speed and do a rate conversion between the two ports if the Ethernet speed is different.

When the same Ethernet speed for both ports is enabled, the Media Converter can be configured for Cut-Through Forwarding. This will increase the media converter’s throughput and reduce latency by performing packet forwarding in the most efficient manner possible. Forwarding of a packet will begin as soon as the destination address is processed

Fiber Interface LoopbackDisable (Default - Up)

In this mode, all frames received on the fiber port in loopback mode will be transmitted back. This provides users with the capability of utilizing their own in-house test generators for testing the link.

Copper NegotiationAuto (Default - Up)

In this mode, the media converter will auto negotiate copper link parameters. When switch is down, the media converter will be in manual mode and will use the parameters as define by Copper Duplex and Copper Speed switches

Copper DuplexFull Duplex (Default - Up)

In this mode, the copper port will be set to full duplex mode. If switch is down, the copper port is set to half duplex mode

Copper Speed100Mbps (Default - Up)

In this mode, the copper port will be fixed at 100 Mbps. When switch down, the copper port will be fixed at 10 Mbps. Note: Copper Negotiation switch must be set to manual for Copper Speed switch to work.

Connectors
1 x RJ4510/100/1G/2.5G/10Gbase-T
IEEE 802.3an
100 meters on CAT6A or better
1 x SFP / SFP+ Transceiver slot
Power level 1 (1 watt) and level 2 (1.5 watts) as per SFP-8431
Hot insertion and removable
Supported 10 Gigabit Fiber pluggable transceivers (IEEE 802.3ae compliant):
  • 10Gbase-SR

  • 10Gbase-LRM

  • 10Gbase-LR

  • 10Gbase-ER

  • 10Gbase-ZR

  • CWDM/DWDM


Supported 1 Gigabit Copper SFPs
  • 1000base-T

  • 1000base-T SGMII


Supported Gigabit Fiber SFPs
  • 1000base-SX

  • 1000base-LX/LH

  • 1000base-EX

  • 1000base-ZX

  • 1000base-BX

  • CWDM/DWDM

Supported 10 Gigabit Fiber pluggable transceiversIEEE 802.3ae compliant:
  • 10Gbase-SR

  • 10Gbase-LRM

  • 10Gbase-LR

  • 10Gbase-ER

  • 10Gbase-ZR

CWDM/DWDM
Environmental Specifications
Operating Temperature0° C to 50° C (32° F to 122° F)
Storage Temperatureminimum range of -25° C to 70° C (-13° F to 158° F)
Operating Humidity5% to 90% non-condensing
Storage Humidity5% to 95% non-condensing
Operating AltitudeUp to 3,048 meters (10,000 feet)
Heat Output
( BTU/HR )
53
MTBF (Hours)**Without power adaptor: 142,577

With power adaptor: 96,646

**Calculation model based on MIL-HDBK-217-FN2 @ 30 °C

Chassismetal with an IP20 ingress protection rating
Mounting
Din Rail KitOptional
Wall / Rack Mount KitOptional
Product Weight and Dimensions
Product Weight0.36 kg, 0.8 lbs
Product Dimensions8 x 12 x 4.2 cm (3.1 x 4.7 x 1.7 inches)
Shipping Weight0.64 kg, 1.41 lbs
Shipping Dimensions26 x 17 x 7 cm (10.2 x 6.7 x 2.8 inches)
Regulatory Approvals
EmissionsFCC Part 15 Class A, EN55022 Class A
CISPR 22 Class A
CISPR 32:2015/EN 55032:2015 (Class A)
CISPR 24:2010/EN 55024:2010
EN61000-3-2
ImmunityEN55024
Electrical SafetyUL 60950-1
IEC 60950-1(ed 2); am1, am2
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
CE
EnvironmentalReach, RoHS and WEEE Compliant
OtherECCN: 5A991
HTSUS Number: 8517.62.0050
Perle Limited Lifetime Warranty