中国电气传动网

第一电气传动平台



总访问量:283483

关键词搜索:

  • 电机
  • 济南鑫贝西
  • 上海仪电
  • 英国马尔文
  • 传感器
  • 发电机
  • 机器人
  • 工业机器人
  • 数控

扫一扫

了解更多

S-10GR-STS 媒体转换器

点击图片查看原图
 
单价: 面议
品牌: Perle
销量: 累计出售 0
评价: 已有 0 条评价
人气: 已有 53 人关注
更新: 2019-07-23
数量: 减少 增加件 库存100件
立即购买   加入购物车   点击询价
       
 
公司基本资料信息
 

Perle S-10GR-STS媒体转换器通过多模或单模光纤透明地连接1G和10G以太网链路。 每个媒体转换器都配有两个可插拔收发器端口,支持光纤到光纤,铜到光纤或铜到铜介质的转换。


The S-10GR-STS Media Converter supports key features for ultimate network flexibility and growth.

  • 1G and 10G rate conversion can be enabled to automatically detect Ethernet port speed and do a rate conversion between the two ports if the Ethernet speed is different. This is ideal in scenarios where disparate networks need to be connected.

  • Cut-Through Forwarding can be configured for environments where throughput speed is critical. This will increase the media converter’s throughput and reduce latency by performing packet forwarding in the most efficient manner possible.

Fiber to Fiber and Copper to Fiber conversion is achieved by inserting SFP or SFP+ fiber transceivers that support multimode and single-mode fiber, including CWDM/DWDM wavelengths. Copper to copper is achieved by inserting SFP or SFP+ Direct Attach Cable (DAC), also known as twinax, transceivers.

The two empty transceiver ports on the S-10GR-STS Media Converters allow for flexible network configurations to meet any requirement using a variety of transceivers supplied by PerleCisco or other manufacturers of MSA compliant SFPs. You can use the S-10GR-STS to convert:

Copper to Fiber Conversion (1G and 10G)

  • 1G Copper SFP to 1G Fiber SFP

  • 1G Copper SFP/SFP+ to 10G Fiber SFP+

Fiber to Fiber Conversion (1G and 10G)

  • 1G Fiber SFP to 1G Fiber SFP

  • 1G Fiber SFP to 10G Fiber SFP+

  • 10G Fiber SFP+ to 10G Fiber SFP+

Copper to Copper Conversion (1G and SGMII)

  • 1G Copper SFP to 1G Copper SFP

The Perle S-10GR-STS Media Converter provides an economical path to extend Ethernet data transmission distances or convert network speeds. Network Administrators can “see-everything” with Perle’s advanced features such as Smart link Pass-Through, Fiber Fault alert and Loopback. This allows for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make the Perle S-10GR-STS Media Converter the smart choice for IT professionals. If you need a Media Converter that can operate in a managed environment with AAA security, check out the SMI-10GR-STS.

S-10GR-STS Media Converter Features

Rate ConversionThe Media Converter can automatically detect Ethernet port speed and do a rate conversion between the two ports if the Ethernet speed is different.
Cut-Through ForwardingWhen the same Ethernet speed for both ports is enabled, the Media Converter can be configured for Cut-Through Forwarding. This will increase the media converter’s throughput and reduce latency by performing packet forwarding in the most efficient manner possible. Forwarding of a packet will begin as soon as the destination address is processed.
SFP Speed SensingAutomatically detects whether a SFP has been inserted and adjusts the speed accordingly
SGMII Interface SupportThe Media Converter supports 1000Mbps SGMII SFPs on port 1.
Smart link Pass-ThroughWhen the Smart link Pass-Through switch is enabled (default), each port will reflect the state of its port peer. In this mode, if a link loss is detected on one port, the transmit signal on the other port is disabled “passing through” the state of the failed link. This enables managed switches and other devices to report link failures to their network NMS.

When the switch is in the down position, Smart link Pass-Through is disabled. If a link loss is detected on one port, the transmit signal remains enabled on the other port.
Fiber Fault alertWith Fiber Fault alert the state of the 10 Gigabit Ethernet receiver is passed to the transmitter. This provides fault notification to the partner device attached to the 10G Ethernet interface of the media converter.
3R – Optical Signal RegenerationOptical signal regeneration: 3R ( Re-amplify, Reshape, and Retime the signal ) ensures that there is a quality link at 10 Gigabit speeds.
Module Temperature ProtectionProtects your DOM/DMI capable SFP or SFP+ module by monitoring its internal temperature and will automatically shut down the SFP or SFP+ if the module is operating above its maximum temperature threshold.
Gigabit SFP supportThe 10 Gigabit media converter model with dual SFP+ slots can also support Gigabit (1000base-X) SFPs. This allows users to use Gigabit SFPs today and migrate to 10G SFP+ in the future. Both slots must be populated with Gigabit SFPs.
Jumbo PacketsTransparent to Jumbo frames with a maximum MTU size of 10,024 bytes
VLANTransparent to VLAN tagged packets.
Power Strain Relief strapA strain relief strap is provided to ensure a solid and secure power connection to the media converter. Ideal for areas that may be exposed to any vibration.
Remote LoopbackCapable of performing a loopback on each 10 Gigabit interface. In this mode, all frames received on the port in loopback mode will be transmitted back. This provides users with the capability of utilizing their own in-house test generators for testing the link.


硬件:

Power
Input Supply Voltage9 - 30 vDC, unregulated ( 12 vDC Nominal )
Maximum Power Consumption18.2 watts*
Total Transceiver power supports3.0 watts
Power Connector5.5mm x 9.5mm x 2.1mm barrel socket
Power Adapter
Universal AC/DC Adapter100-240v AC, regulated AC/12v DC adapter included
Indicators
Power / TST
  • On: Power indication and in normal operation

  • Blinking slowly: the unit is in loopback or test mode (either port)

  • Red solid: the unit has a hardware error (upon power up)

  • Red and blinking: the unit has a hardware error specified by combination of LK1 and LK2

LK1, LK2
  • On: Fiber link present

  • Blinking quickly: Fiber link present and receiving data.(including test data)

  • Blinking slowly: Fiber link disabled because the other fiber link went down.

  • Blinking 1 sec on 3 sec off – module shut down due to high temperature.

  • Off: No fiber link present or no module inserted

Switches - accessible through a side opening in the chassis
Smart link Pass-ThroughEnabled (Default - Up)

When the Smart link Pass-Through switch is enabled (default), each port will reflect the state of its port peer. In this mode, if a link loss is detected on one port, the transmit signal on the other port is disabled “passing through” the state of the failed link. This enables managed switches and other devices to report link failures to their network NMS.

When the switch is in the down position, Smart link Pass-Through is disabled. If a link loss is detected on one port, the transmit signal remains enabled on the other port.

Fiber Fault alertEnabled (Default - Up)

With Fiber Fault alert the state of the 10 Gigabit ethernet receiver is passed to the transmitter. This provides fault notification to the partner device attached to the 10G ethernet interface of the media converter.

Cut-through / Rate convertingRate Converting (Default - Up)

The Media Converter can automatically detect Ethernet port speed and do a rate conversion between the two ports if the Ethernet speed is different.

When the same Ethernet speed for both ports is enabled, the Media Converter can be configured for Cut-Through Forwarding. This will increase the media converter’s throughput and reduce latency by performing packet forwarding in the most efficient manner possible. Forwarding of a packet will begin as soon as the destination address is processed

Fiber Interface LoopbackDisable (Default - Up)

When enable, the media converter will be in fiber loopback mode. In this mode all frames received on the fiber port will be transmitted back. This provides users with the capability of utilizing their own in-house test generators for testing the link

Loopback InterfacePort 1(Default - Up)

In this mode, all frames received on the fiber port 1 in loopback mode will be transmitted back. When switch is set down, port 2 will be in loopback mode and transmitting all frames received back.

Connectors – Two SFP / SFP+ Transceiver Slots. Hot insertion and removable.
Supported 10 Gigabit Fiber SFP+ TransceiversPower Levels 1 and 2 IEEE 802.3ae compliant:
  • 10Gbase-SR

  • 10Gbase-LRM

  • 10Gbase-LR

  • 10Gbase-ER

  • 10Gbase-ZR

CWDM/DWDM
Supported 1 Gigabit Copper SFPs

1000base-T

1000base-T SGMII

Supported Gigabit Fiber SFPs

Standard SFP Power level 1 (1 watt) and level 2 (1.5 watts) as per SFP-8431

1000base-SX

1000base-LX/LH

1000base-EX

1000base-ZX

1000base-BX

CWDM/DWDM

Environmental Specifications
Operating Temperature0° C to 50° C (32° F to 122° F)
Storage Temperatureminimum range of -25° C to 70° C (-13° F to 158° F)
Operating Humidity5% to 90% non-condensing
Storage Humidity5% to 95% non-condensing
Operating AltitudeUp to 3,048 meters (10,000 feet)
Heat Output
( BTU/HR )
62
MTBF (Hours)Without power adaptor: 115,765

With power adaptor: 88,506

Calculation model based on MIL-HDBK-217-FN2 @ 30 °C

Chassismetal with an IP20 ingress protection rating
Mounting
Din Rail KitOptional
Wall / Rack Mount KitOptional
Product Weight and Dimensions
Product Weight0.36 kg, 0.80 lbs
Product Dimensions8 x 12 x 4.2 cm (3.1 x 4.7 x 1.7 inches)
Shipping Weight0.64 kg, 1.41 lbs
Shipping Dimensions26 x 17 x 7 cm (10.2 x 6.7 x 2.8 inches)
Regulatory Approvals
EmissionsFCC Part 15 Class A, EN55022 Class A
CISPR 22 Class A
CISPR 32:2015/EN 55032:2015 (Class A)
CISPR 24:2010/EN 55024:2010
EN61000-3-2
ImmunityEN55024
Electrical SafetyUL 60950-1
IEC 60950-1(ed 2); am1, am2
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
CE
Laser SafetyDependent on SFPs used. SFPs that meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11 are recommended for use with this product.
EnvironmentalReach, RoHS and WEEE Compliant
OtherECCN: 5A991
HTSUS Number: 8517.62.0050
Perle Limited Lifetime Warranty